Ordering no:
Female cable connector, power, S-Coding
Female cable connector, power, S-Coding, Series 814 S-Coding
Available numbers of contacts
99 0686 19 03
M12-S female cable connector, Contacts: 3, 8,0 - 10,0 mm, screw clamp, IP67, UL
M18, series 814, Automation technology - sensors and actuators
| Artikelnummer |
99 0686 19 03
|
| Connector locking system | bolted |
| Termination | screw clamp |
| Wire gauge (mm) | 1,5 mm² |
| Wire gauge (AWG) | 16 |
| Cable outlet | 8,0 - 10,0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 100 Mating cycles |
| Upper temperature | 85 °C |
| Lower temperature | -40 °C |
| Rated current (40°C) | 16 A |
| Rated voltage | 630 V |
| Rated impulse voltage | 6000 V |
| Pollution degree | 3 |
| Overvoltage category | III |
| Material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Material of contact | CuZn (brass) |
| Contact plating | Au (gold) |
| Material of contact body | PA |
| Material of housing | PA |
| Approval 1 | UL |
| Customs tariff number | 85369010 |
| Weight (g) | 25.912 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The end user must take suitable safety measures to ensure that the connector cannot be disconnected accidentally.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Downloads
Gegevensblad
Certificates
CAD files
99 0690 19 04
M12-S female cable connector, Contacts: 4, 8,0 - 10,0 mm, screw clamp, IP67, UL
M18, series 814, Automation technology - sensors and actuators
| Artikelnummer |
99 0690 19 04
|
| Connector locking system | bolted |
| Termination | screw clamp |
| Wire gauge (mm) | 1,5 mm² |
| Wire gauge (AWG) | 16 |
| Cable outlet | 8,0 - 10,0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 100 Mating cycles |
| Upper temperature | 85 °C |
| Lower temperature | -40 °C |
| Rated current (40°C) | 12 A |
| Rated voltage | 630 V |
| Rated impulse voltage | 6000 V |
| Pollution degree | 3 |
| Overvoltage category | III |
| Material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Material of contact | CuZn (brass) |
| Contact plating | Au (gold) |
| Material of contact body | PA |
| Material of housing | PA |
| Approval 1 | UL |
| Customs tariff number | 85369010 |
| Weight (g) | 26.5 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The end user must take suitable safety measures to ensure that the connector cannot be disconnected accidentally.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Downloads
Gegevensblad
CAD files
Contact to customer service
Do you have any questions regarding our products or do you wish an individual offer?